Home

The
BLOODHOUND
Project

The Bloodhound Project Andy Green’s Diary – March 2014

Andy Green’s Diary – March 2014

Monday, 31 March, 2014

The build programme for our 1000 mph Car marches on. BLOODHOUND SSC is the kit car from hell, with around 3500 bespoke components, plus fasteners (including 15,000+ rivets in the rear chassis alone). Of course, that doesn’t stop me greeting the team with a helpful ‘Hi guys – have you finished it yet?’ each time I go down there. Not just yet, is the answer, but we’re still on track to run in South Africa next year.

Campbell rules the World Record, 1924

Great news for the Project, with the recent announcement of Castrol joining as a major sponsor. They have been part of an amazing total of 21 World Land Speed Records, going back to 1924. In an era when milk was still being delivered on horse-drawn milk floats, the company was supporting Malcolm Campbell in setting his first World Record, at an astonishing 146 mph. Most recently, Castrol supported Thrust SSC in 1997, when we hit 763 mph and became the only supersonic Record Car in history. Now the company is up for an even bigger Engineering Adventure. Well done them. Check out the video here.

A key part of running a Land Speed Record Car is being able to stop it, as discussed in last month’s update. BLOODHOUND will have a truly huge amount of energy at 1000 mph – about 660 Mega Joules. To put that in perspective, a High Speed Train, blasting along at 125 mph, has about 560 Mega Joules of energy – 100 less than BLOODHOUND. It’s enough energy to boil over 300,000 kettles, so it’s a safe bet that we can’t stop BLOODHOUND with wheel brakes alone.

Our brilliant aerodynamicist and performance expert, Ron Ayers, has calculated that about 52% of BLOODHOUND’s energy will be absorbed by aerodynamic drag, 36% will be absorbed by the airbrakes (and/or drag chutes) and 11% will be dissipated by the vehicle’s rolling resistance. That makes 99%. The remaining 1% will be absorbed by the Car’s wheel brakes.

A short 9000 ft of Newquay test track

If the wheel brakes are only going to absorb a measly 1% of the energy, then why are we even bothering to fit them? Well, partly because we need them for the UK runway tests next year, at the Newquay Aero Hub, where the brakes will have to do most of the work. Want to come and watch? Join our Supporters Club Gold Members and we’ll send you an invitation.

For the runway runs, BLOODHOUND will have brakes on all 4 wheels, with dual circuits, to give us lots of stopping power and redundancy. The runway at Newquay is 2700 m (9000 ft) long, which is huge until you’re doing 200+ mph in a 6 tonne Car, when it’s not quite so huge anymore. We’ll be using carbon/carbon brakes, the same as those used by aircraft and high-performance race cars, to give us the best braking performance on the runway.

When we get to the desert, the brakes are less important, as they are only doing 1% of the work. It’s an important last bit though. There’s no point in getting 99% of the braking done and then trundling off the end of Hakskeen Pan at 50 mph. That would just be embarrassing. The wheel brakes will shorten the stopping distance by about half a mile and they will also let me slow the Car down to walking speed, turn it through 180 degrees and stop right next to the turn-round crew. The FIA Land Speed Record regulations require 2 runs in opposite directions, within one hour, so turning round and stopping in exactly the right place is a key part of it.

Almost (but not quite) 1000 mph at ground level

There is a problem with wheel brakes on the desert, though. We won’t need to use them at 1000 mph, but they will still be along for the ride, at over 10,000 rpm (that’s 170 revolutions per second). We tested a carbon fibre brake disc at 10% above this spin speed, to give us a safety margin. The disc exploded. This carbon disc was one of the best in the world, the same specification as the RAF’s new Typhoon jet uses. We already knew that no jet fighter has ever flown at 1000 mph at ground level, and now we know their brakes won’t survive it either. We need another solution.

The proposed alternative is an unusual one, using steel discs. No-one uses steel for brake discs. Steel doesn’t absorb as much energy as carbon and it can be damaged by the extreme heat that race car brakes experience. Steel does have one key advantage for us though – it’s stronger than a carbon disc. Steel will survive the extreme loads at 1000 mph, but the question is, will it survive exposure to 1% of BLOODHOUND’s huge amount of energy?

Brakes at volcano temperatures

To test the steel brake discs, we went to AP Racing, where the rest of BLOODHOUND’s brake assembly has been made. We cranked their rig up as fast as it could go, which equates to around 160 mph for BLOODHOUND. The test team did 10 full stops from maximum speed on the same steel disc. Maximum temperature on the disc was around 1100 deg C, roughly the same temperature as the inside of a volcano. Harsh conditions for a brake disc – have a look at this video to see just how tough.

The good news is that the aluminium brake calliper (the fixed bit that holds the pads and brake mechanism) only hit 150 deg C, so no problems there. The final bits of the test are to conduct a metallurgical analysis of our super-heated steel disc, to check it’s still OK, and then spin it up to over 10,000 rpm (simulating 1000+ mph) to make sure it can still cope. Once it survives all of that, then we’ve found our desert wheel braking solution. It’s only 1%, but it’s an important 1%.

Strong enough for 3 of me

Travelling at 1000 mph brings some other interesting challenges. To get into the cockpit, I will climb down through an oval canopy hatch positioned on the top of the cockpit. This area is subject to a very low pressure at supersonic speeds, as the air accelerates over the cockpit, and this low pressure will try to tear the cockpit hatch off the Car. At supersonic speeds, that will make my 1000 mph office more than a little windy. The hatch would then immediately be eaten by the EJ200 jet engine, destroying both hatch and engine, which is also not ideal.

To make sure that the hatch stays on, our stress expert Roland has put a lot of work into making sure that the canopy latches are strong enough. The finished result has just been delivered and looks great. The latch doesn’t look much, but it’s stressed to a normal working load of 2,5 kN (quarter of a tonne) – that’s 3 large guys hanging off this little handle all at the same time.

Just behind the ‘office’, the HTP tank (containing one tonne of rocket oxidiser) needs to slot into the carbon fibre monocoque. The rocket will burn off the whole one tonne load of HTP in a little over 20 seconds, at the centre of the Car, to make sure that the vehicle’s Centre of Gravity doesn’t move too much. This will put the HTP tank directly behind my cockpit, but I’ve been promised that there are lots of bulkheads and seals to prevent the HTP joining me in the cockpit at any stage.

A tight squeeze, but it fits

Meanwhile, the tank has now had its first test-fit inside the monocoque. It’s snug, but it all fits nicely, and we can reach all the key points to install the plumbing and to service it.

180 hours of work later

The front suspension is also coming along well, with AMRC completing the upper section and now working on the lower parts. They look simply stunning and I can’t wait to see them all on the Car. Each upper section was machined from a forged block of aerospace grade aluminium, provided by thyssenkrupp Materials, measuring the size of a coffee table and weighing 300 kg. After 180 hours of machining, we’re left with an upper suspension piece now weighing just 18 kg, with over 280 kg of material to be recycled for next time.

This phase of BLOODHOUND’s engineering is all about details. Any mistakes we make now will cost us dear, when we get to the desert in South Africa next year and things don’t work as they should. If we’re going to have a world-class Engineering Adventure, and push the boundaries of physics at 1000 mph, and do it all safely, then we need to get the details right first time. It’s a fascinating process to watch, as it all starts to come together.

Still checking……